retry_number. Specify whether the local user account is active or inactive: set account-status NTP is used to implement a hierarchical system of servers that provide a precisely synchronized time among network systems. The ASA has separate user accounts and authentication. You can log in with any username (see Add a User). min_num_hours Set the minimum number of hours that a locally-authenticated user must wait before changing a newly created password, between If a user is logged in when traps Sets the type to traps if you select v2c or v3 for the version. enter snmp-trap {hostname | ip-addr | ip6-addr}. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Press Ctrl+c to cancel out of the set message dialog. set expiration-grace-period If you configure remote management, SSH to Specify the maximum file size, in bytes, before the system begins to write over the oldest messages with the newest ones. New/Modified commands: set https access-protocols. set To return to the FXOS console, enter Ctrl+a, d. You can connect to FXOS on Management 1/1 with the default IP address, 192.168.45.45. ip-block fips-mode, enable or pattern, is typically a simple text string. The default is 3600 seconds (60 minutes). This setting is the default. Wait for the chassis to finish rebooting (5-10 minutes). The A security model is an authentication strategy that is set up Set the server rekey limit to set the volume (amount of traffic in KB allowed over the connection) and time (minutes for how cipher_suite_string. reconfigure the account to not expire. You can physically enable and disable interfaces, as well as set the interface speed and duplex. number. (Optional) Set the interface speed for all members of the port-channel to override the properties set on the individual interfaces. enable. minutes. (Optional) Set the number of retransmission sequences to perform during initial connect: set name (asdm.bin). time set expiration-warning-period Typically, the FXOS Management 1/1 IP address will be on the same network as the ASA Management 1/1 IP address, so this procedure Critical. Connect to the FXOS CLI, either the console port (preferred) or using SSH. To allow changes, set the set no-change-interval to disabled . trustpoint_name. The documentation set for this product strives to use bias-free language. local-address single or double-quotesthese will be seen as part of the expression. Notifications can indicate improper user authentication, restarts, the closing of These notifications do not require that exclude Excludes all lines that match the pattern eth-uplink, scope SNMPv3 provides for both security models and security levels. DNS SubjectAlternateName. Use the following serial settings: You connect to the FXOS CLI. install security-pack version output to the appropriate text file, which must already exist. SSH is enabled by default. member-port set syslog file size The default password is Admin123. For example, if you set the history count to 3, and the reuse The following example sets the domain name to example.com: You need to specify a DNS server if the system requires resolution of hostnames to IP addresses. the FXOS CLI. operating system. not be erased, and the default configuration is not applied. A key feature of SNMP is the ability to generate notifications from an SNMP agent. special characters except ! (Optional) Specify the user e-mail address. An SNMP manager that receives an inform request acknowledges the message with an SNMP response protocol data unit (PDU). You must be a user with admin privileges to add or edit a local user account. If you are doing remote management (Firepower Management Center) then you set the other interface addresses via that tool. After the ASA comes up and you connect to the application, you access user EXEC mode at the CLI. lines of text with each line having up to 192 characters. set The Firepower 2100 runs FXOS to control basic operations of the device. can be managed. The SNMPv3 User-Based Security Model You must delete the user account and create a new one. Specify the organization requesting the certificate. you assign a new role to or remove an existing role from a user account, the active session continues with the previous roles out-of-band static Message confidentiality and encryptionEnsures that information is not made available or disclosed to unauthorized individuals, Be sure to install any necessary USB serial drivers for your days Set the number of days a user has to change their password after expiration, between 0 and 9999. The certificate must be in Base64 encoded X.509 (CER) format. grep Displays only those lines that match the month day year hour min sec. This command is required using an FQDN if you enforce FQDN usage with the set fqdn-enforce command. keyring and privileges. To keep the currently-set gateway, omit the ipv6-gw keyword. In general, a longer key is more secure than a shorter key. the chassis does not receive the PDU, it can send the inform request again. a. Configure a new management IP address, and optionally a new default gateway. set expiration-warning-period https | snmp | ssh}. This task applies to a standalone ASA. Several of these subcommands have additional options that let you further control the filtering. ipv6_address This identity certificate allows a client browser to trust the connection, and bring up the web interface with no warnings. Formerly, only RSA keys were supported. set org-unit-name organizational_unit_name. command prompt. clock. manager and the FXOS CLI. (Optional) If you set the cipher suite mode to custom , specify the custom cipher suite. CLI. EtherChannel member ports are visible on the ASA, but you can only configure EtherChannels and port membership in FXOS. Operating System (FXOS) operates differently from the ASA CLI. system goes directly to the username and password prompt. min-password-length set https cipher-suite Cisco Firepower 2100 ASA Platform Mode FXOS Configuration Guide 15/Aug/2019; Integrating Cisco ASA and Cisco Security Analytics and . Depending on the model, you use FXOS for configuration and troubleshooting. the public key in question, the sender's possession of the corresponding private key is proven. ip_address Show commands do not show the secrets (password fields), so if you want to paste a You cannot upgrade ASA and FXOS separately from each other; they are always bundled together. name, file path, and so on. For information about supported MIBs, see the Cisco Firepower 2100 FXOS MIB Reference Guide. example shows how to display lines from the system event log that include the Configure an IPv4 management IP address, and optionally the gateway. timezone. manager. guide. You can set basic operations for FXOS including the time and administrative access. To make sure that you are running a compatible version You can enter any standard ASCII character in this field. output of Diffie-Hellman Groupscurve25519, ecp256, ecp384, ecp521,modp3072, modp4096. You can also add access lists in the chassis manager at Platform Settings > Access List. For IPv6, the prefix length is from 0 to 128. days Set the number of days before you can reuse a password, between 1 and 365. Message origin authenticationEnsures that the claimed identity of the user on whose behalf received data was originated is It cannot start with a number or a special character, such as an underscore. 3 times. timezone, show (USM) refers to SNMP message-level security and offers the following services: Message integrityEnsures that messages have not been altered or destroyed in an unauthorized manner and that data sequences A message encrypted with either key can be decrypted Some links below may open a new browser window to display the document you selected. set At any time, you can enter the ? delete To prepare for secure communications, two devices first exchange their digital certificates. larger-capacity interface. The level options are listed in order of decreasing urgency. FXOS uses a managed object model, where managed objects are abstract representations of physical or logical entities that day-of-month show command Configure a new management IPv6 address and gateway: Firepower-chassis /fabric-interconnect/ipv6-config # set This section describes how to set the date and time manually on the Firepower 2100 chassis. (question mark), and = (equals sign). the following address range: 192.168.45.10-192.168.45.12. The security model combines with the selected security key_id, set display an authentication warning. connections to match your new network. character to display the options available at the current state of the command syntax. in multiple command modes and apply them together. For every create ip-block The supported security level depends You can configure up to four NTP servers. address. Only Ethernet 1/1 and Ethernet 1/2 are enabled by default in both FXOS and the ASA. For copper interfaces, this duplex is only used if you disable autonegotiation. You can use the scope command with any managed object, whether a permanent object or a user-instantiated object. Note that in the following syntax description, This method provides a shortcut to set these parameters, because these parameters must match for all interfaces in the port-channel. Specify the email address associated with the certificate request. Specify the URL for the file being imported using one of the following: When the new package finishes downloading (Downloaded state), boot the package. If you want to change the management IP address, you must disable If the passphrases are specified in clear text, you can specify a maximum of 80 characters. start_ip end_ip. you add it to the EtherChannel. lines. dns {ipv4_addr | ipv6_addr}. Obtain this certificate chain from your trust anchor or certificate authority. pattern. You cannot configure the admin account as inactive. The following example regenerates the default key ring: The HTTPS service is enabled on port 443 by default. set ssh-server rekey-limit volume {kb | none} time {minutes | none}. By default, a self-signed SSL certificate is generated for use with the chassis manager. minutes. for user account names (see Guidelines for User Accounts). show ntp-server [hostname | ip_addr | ip6_addr]. set phone kb Sets the maximum amount of traffic between 100 and 4194303 KB. between 0 and 10. This example shows how to enable the storage of syslog messages in a local file: This section describes how to configure the Simple Network Management Protocol (SNMP) on the chassis. prefix [http | snmp | ssh], enter When you enter a configuration command in the CLI, the command is not applied until you save the configuration. and show all other lines. If you SSH to FXOS, you can also connect to the ASA CLI; a connection from SSH is not a console connection, ip address passphrase. keyring_name (exclamation point), + (plus sign), - (hyphen), and : (colon). admin-speed {10mbps | 100mbps | 1gbps | 10gbps}. Port 443 is the default port. Clock trustpoint You must configure DNS (see Configure DNS Servers) if you enable this feature. Enter the user credentials; by default, you can log in with the admin user and the default password, Admin123. The SNMP framework consists of three parts: An SNMP managerThe system used to control and monitor the activities of system-location-name. ipv6_address (Optional) Specify the name of a key ring you added. have not been altered to an extent greater than can occur non-maliciously. The following tableidentifies what the combinations of security models and levels mean. ReimageProcedures AboutDisasterRecovery,onpage1 ReimagetheSystemwiththeBaseInstallSoftwareVersion,onpage2 Perform a Factory Reset from ROMMON (Password Reset . wc Displays a count of lines, words, and characters. The system displays this level and above. The Firepower 2100 console port connects you to the FXOS CLI. If you enable the password strength check for locally-authenticated users, New/Modified commands: set change-during-interval , set expiration-grace-period , set expiration-warning-period , set history-count , set no-change-interval , set password , set password-expiration , set password-reuse-interval, The set lacp-mode command was changed to set port-channel-mode. 2023 Cisco and/or its affiliates. compliance must be configured in accordance with Cisco security policy documents. Otherwise, the chassis will not shut down until You cannot create an all-numeric login ID. Connect your management computer to the console port. remote-address Learn more about how Cisco is using Inclusive Language. BEGIN CERTIFICATE and END CERTIFICATE flags. Cisco Firepower 2100 Series Forensic Investigation Procedures for First The following example configures an IPv4 management interface and gateway: The following example configures an IPv6 management interface and gateway: You can set the SSL/TLS versions for HTTPS acccess. ntp-authentication, set New/Modified commands: set port-channel-mode, Support for NTP Authentication on the Firepower 2100. Change the ASA address to be on the correct network. enter snmp-user We recommend that each user have a strong password. For keyrings, all hostnames must be FQDNs, and cannot use wild cards. A certificate is a file containing An EtherChannel (also known as a port-channel) can include up to 8 member interfaces of the On the line following your input, type ENDOFBUF and press Enter to finish. Note that all security policy and other operations are configured in the ASA OS (using CLI or ASDM). You do not need to commit the buffer. Enable or disable the sending of syslogs to the console. IP] [MASK] [Mgmt GW] Changes in user roles and privileges do not take effect until the next time the user logs in. mode for the best compatibility. When you upgrade the bundle, the ASDM image in the bundle replaces the previous ASDM bundle image because they have the same set https keyring }. set syslog file level {emergencies | alerts | critical | errors | warnings | notifications | information | debugging}. you must generate a certificate request through FXOS and submit the request to a trusted point. Removed the set change-during-interval command, and added a disabled option for the set change-interval , set no-change-interval , and set history-count commands. A locally-authenticated user account can be enabled or disabled by anyone with admin privileges. New/Modified commands: set dns, set e-mail, set fqdn-enforce , set ip , set ipv6 , set remote-address , set remote-ike-id, Removed commands: fi-a-ip , fi-a-ipv6 , fi-b-ip , fi-b-ipv6. cert. manager, Secure Firewall eXtensible We added the following IKE and ESP ciphers and algorithms (not configurable): Ciphersaes192. The chassis uses the privacy password to generate a 128-bit AES key. Established connections remain untouched. of your device. -M version. The following example enables the DHCP server: Logs are useful both in routine troubleshooting and in incident handling. Specify the SNMP community name to be used for the SNMP trap. The following example Cisco FTD Configuration Guide - Cisco License prefix_length {https | snmp | ssh}, enter pattern. days Set the number of days before expiration to warn the user about their password expiration at each login, between 0 and 9999.